Test Equipment

The motion analysis of rotating machines is quick and easy with our stroboscope. The stroboscope is equipped with 3 high-power LEDs, collectively producing a light intensity of 11,730 Lux at 20 cm / 1000 Hz. With the stroboscope, you can precisely adjust the flash frequency in both FPM and Hz. Additionally, it is compact, portable, and operates independently thanks to the built-in battery.

- 3 High Power LEDs
- 6160 lux at 30 cm / 1000 Hz
- digital pulse width modulation
- phase shift: -360° to +360°

more

The thickness meter can measure material thicknesses up to 300 mm / 11.81". So that the material thickness of a wide variety of homogeneous materials can be measured, it is possible to store the corresponding speed of sound in the thickness meter. For materials such as steel, aluminum, zinc, silver and gold, the appropriate sound speeds are already stored in the device library. This means that the thickness meter can be used universally.

- thickness measurement up to 300 mm / 11.81
- measured value memory
- calibration reference on the housing
- limit alarm
- different models available
more

The PCE-BTM 2000 is a measuring instrument to determine the tension of V-belts or drive belts. Belt tension can only be measured when the belt is not in operation. A small impulse with the help of a beater is enough to make the belt vibrate. With a measuring probe and a sensor beam, the generated vibration frequency is determined.

- data memory
- high accuracy
- TFT colour display 2.4"
- belt tension displayed in newton

more

For many materials such as, iron, steel, aluminum, copper, brass and stainless steel

- measurement range: Fe: 0 ... 5000 μm, non-Fe: 0 ... 3000 μm
- measurements not influenced by vibrations
- practical V-groove on the measuring heads
- ergonomic design
- various optional sensors available


more

A portable handheld non-destructive conductivity tester for metals. This non-destructive testing (NDT) device uses eddy current to determine the electrical conductivity of non-ferrous metals such as aluminum and copper. Includes 3 standards for testing.

- operating frequency: 60 kHz
- sine wave probe: Ø 14 mm / ≈ 0.55 in
- memory: Up to 500 groups of measurements
- lift-off and temperature compensation
- comes with ISO calibration certificate

more

Up to 800 Hz sample frequency for acceleration (3-axis), temperature, humidity, air pressure, and light sensors.

- 3-axis acceleration up to 800 Hz
- for temperature, humidity, air pressure and light
- 32 GB SD memory card
- small design: 86.8 x 44.1 x 22.2 mm / 3.4 x 1.7 x 0.87 in

more

With a measurement range of 2,400 mT, the electromagnetic field meter covers a wide range of measuring tasks. The electromagnetic field meter has an accuracy of 1 % which makes it a very precise meter. The electromagnetic field meter can be used, for instance, to test relays and permanent magnets for existing magnetic fields. It is therefore often used in production processes or in quality control.

- very precise measurement technology
- measurement range up to 24,000 G and 2,400 mT
- transversal and axial sensor
- measures static magnetic fields
- automatic shutdown

more

The PCE-DFG X force measurement device series is used for traction and compression force measurements. The force gauges provide high accuracy 0.05 % FS.

- force gauges with internal dynamometric cell up to 5 N, 10 N, 20 N, 200 N, 500 N, 1,000 N
- accuracy ±0.05 % FS
- sampling rate up to 7,200 Hz
- internal memory for 30 x 1,000,000 readings

more

The PCE-DFG K X force gauge series is used for traction and compression force measurements. The force gauges provide high accuracy 0.05 % FS.

- force gauges with external dynamometric cell up to 1 kN, 2.5 kN, 5 kN, 10 kN, 20 kN, 100 kN
- accuracy ±0.05 % FS
- sampling rate up to 7,200 Hz
- internal memory for 30 x 1,000,000 readings

more

The PCE-DFG N force measurement device series is used for traction and compression force measurements. The force gauges provide high resolution of 0.001 N.

- force gauges with internal dynamometric cell up to 2 N, 5 N, 10 N, 20 N, 500 N
- force gauges with external dynamometric cell up to 1 kN, 2.5 kN, 5 kN, 10 kN
- accuracy ±0.1 % FS
- sampling rate 6 ... 1,600 Hz
- internal memory for up to 100 measurements

more

The length measuring device PCE-FD 300 is used in combination with the force test stand PCE-MTS 500 and a force gauge of the PCE-DFG series to make force-displacement measurements. The specially developed in-house software is an important element in this combination of different measuring devices. The software is able to receive the measured values for displacement and force simultaneously via the USB interfaces.

- Force range: max. 5000 N / 500 kg / 1100 lbs
- Travel: max. 300 mm / 11.8"
- Feed speed: 30 ... 230 mm/min / 1.18 ... 9.05 in/min
- Manual or automatic procedure
- incl. length measuring device: -150 … 150 mm / -5.9 … 5.9"

more

The PCE-DFG NF force measurement device series is used for traction and compression force measurements. The force gauges provide high resolution of 0.1 kN.

- force gauges with external dynamometric cell up to 0.5 kN, 1 kN, 20 kN, 50 kN, 100 kN
- accuracy ±0.1 % FS
- sampling rate 6 ... 1,600 Hz
- internal memory for up to 100 measurements

more

The torque meter PCE-DFG N TW series consists of a hand-held measuring device and an external torque transducer. The torque wrench tester is delivered adjusted so that the control measurements can be started immediately.

- measurement range: 5 Nm, 10 Nm, 50 Nm, 100 Nm
- resolution: 0.001 Nm, 0.005 Nm, 0.01 Nm, 0.1 Nm
- measurement uncertainty: ± 0.5% of the measurement range
- memory for 100 measurement series with 8,000 measurement points each
- USB interface including PC software
- graphic display

more

A hydraulic force gauge is based on the principle that the force acting on the plunger is measured hydraulically. The generated hydraulic pressure is displayed by the force transducer on a scale in newton.

- measurement range: 0 ... 10 kN
- resolution: 200 N
- measuring accuracy: ±1.85 % of measurement range

more

Metal hardness meter for HL, HRC, HRB, HB, HV, HSD

- measurement range 200 ... 900 HL
- accuracy ±0.8 % at HLD = 900
- materials 9 different common materials
- conversion HL-HRC-HRB-HB-HV-HSD
- comes with ISO calibration certificate

more

Metal Hardness Meter for HLD, HRC, HRB, HV, HS, HRA with Data Memory

- measurement range 170 ... 960 HLD
- accuracy ±0.5 % at HLD = 800
- 9 different common materials
- measuring direction: 0 ... 360°
- different probes are available
- comes with ISO calibration certificate

more

The melt index tester from PCE Instruments is used for fast testing of the melt mass flow rate of plastics. The melt index tester is designed both for incoming goods inspection and for continuous production monitoring. Due to the clear display of all relevant parameters on the 7" touch display, measurement results can be determined in a short time with the melt index tester.

- large 7" TFT touch display
- clear depiction
- heating temperature up to 400 °C
- materials that have already been predefined

more

The CO₂ data logger is specially designed for long-term monitoring of climatic conditions in, for example, offices, classrooms or lecture halls. The air quality meter has various sensors and an E-paper display.

- measuring range up to 40,000 ppm CO₂
- temperature and humidity
- atmospheric pressure
- E-paper display with histogram display
- .csv file format
- Alarm limits

more

with up to 1600 Hz

- 3- axis acceleration up to 1600 Hz
- 32 GB SD memory card
- small design: 86.8 x 44.1 x 22.2 mm / 3.4 x 1.7 x 0.87 in
- evaluation software

more

The sound level calibrator is a battery-operated sound source. The sound level calibrator allows direct and fast calibration of sound level meters and other noise measuring equipment.

- sound pressure levels 94 and 114 dB
- for weighting filters A, B, C, D
- immediately ready for use
- accuracy class 1, IEC 942
- easy to use
- different microphone dimensions possible

more

The thickness meter with data memory, limit alarm and adjustable speed of sound can measure material thicknesses up to 225 mm

- measuring range: 1.00 ... 225.0 mm / 0.04 ... 8.85"
- resolution: 0.01 mm at ≤99.99 mm / 0.1 mm at ≥100.0 mm
- accuracy: ±0.5% of measured value + 0.05 mm
- memory capacity: 500 measured values
- calibration reference on housing

more

The PCE-TG 300 is a thickness gauge with special sensors for various applications. In general, the wall thicknesses of all homogeneous materials can be measured with the thickness gauge. For attenuating or scattering materials such as plastic or cast a special sensor is available.

- measurement range:
  PE: pulse-echo mode 0.65 ... 600 mm (steel)
  EE: echo-echo mode 2.50 ... 60 mm
- accuracy:
  ± 0.04 mm H [mm] (<10 mm); ± 0.4% H [mm] (> 10 mm) H refers to the material thickness of the workpiece
- resolution: 0.1 mm / 0.01 mm / 0.001 mm (adjustable)

more

The PCE-TDS 200 heat meter is a particularly precise measu-ring device. For a simplified analysis of the measured values, the heat meter offers a wide range of units.

- measuring range ±25 m/s
- software for further analysis of the measured values
- various sensors
- connection of thermocouples
- data memory size of 32 GB
- individually adjustable alarm limits
- display individually adjustable

more

With the evaporation cabinet PCE DLT 10, the water vapour resistance of samples is tested according to AMK-MB-005 (04/2015) Humidity and Climatic Resistance Test Module 1 (water vapour loading). This test simulates the conditions of cooking hobs or dishwashers.

- steam test according to AMK-MB-05
- max. 5 test samples
- automatic test sequence with constant temperature
- good-bad indication of temperature
- determination of moisture expansion
- checking of joint formation and edge release

more

The vibration meter is ideal for maintenance workers to quickly check vibrating parts, machines and systems. This vibration meter shows the vibration acceleration, vibration velocity and vibration displacement directly on the display.

measurement ranges
- acceleration: 0.0 ... 399.9 m/s²
- velocity: 0.00 ... 399.9 mm/s
- displacement: 0.000 ... 3.9 mm
- automatic ISO 10816-3 evaluation
- colored graphic display

more

The vibration analyzer is the ideal companion for checking vibrating parts, machines and systems. RMS, peak, peak-to-peak and crest factor are available as measurement parameters on the vibration data logger with colored graphic display and rechargeable battery.

measurement ranges
- acceleration: 0.0 ... 399.9 m/s²
- velocity: 0.00 ... 399.9 mm/s
- displacement: 0.000 ... 3.9 mm
- automatic ISO 10816-3 evaluation
- 50 memory locations with 43200 measured values each

more

The vibration analyzer has an FFT mode. RMS, peak, peak-to-peak and crest factor are available as measurement parameters on the vibration data logger with rechargeable battery.

measurement ranges
- acceleration: 0.0 ... 399.9 m/s²
- velocity: 0.00 ... 399.9 mm/s
- displacement: 0.000 ... 3.9 mm
- FFT analysis
- route measurement
- 50 memory locations with 43200 measured values each

more

The 4-channel contact thermometer for thermocouples allows for the display and archiving of multiple temperature sensors simultaneously. It can be connected to up to 8 different types of thermocouples. Notably, the data logger offers high accuracy, especially with Type K thermocouples, with an accuracy of ±(0.04% + 0.3 °C).

- measurement range from -200 ... +1800 °C
- compatible with 8 types of thermocouples
- adjustable storage interval from 1 s to 12 h
- display of maximum, minimum, and average values
- storage capacity for 10 million readings
- adjustable alarm thresholds

more

Mobile / stationary wind recorder

- pre-alarm and full alarm with visual and audible warnings
- allows measurement of the slightest wind movements
- optional RS-485 MODBUS interface for data communication
- measurement range: 0 ... 50 m/s
- displays current wind speed or average wind speed of last 2 or 5 minutes
- comes with ISO calibration certificate

more

The wind speed alarm controller PCE-WSAC 50W 230 is primarily used to measure and monitor the wind load on cranes or wind turbines. Furthermore, the wind situation can be measured and analyzed before commissioning a wind turbine. The high measurement range of up to 50 m/s of the wind speed alarm controller means stormy gusts can also be monitored.

- measurement range up to 180 km h
- Input: Pulse, analogue (4 ... 20 mA) or radio transmission
- 4 ... 20-mA analogue output
- Supply voltage: 110 ... 230 V AC, 50/60 Hz
- Units adjustable: km/h, mph, m/s

more

The multi-parameter photometers are a mobile measuring device for liquid analysis. This means that various different measurements can be carried out with the multi-parameter photometer. With these multi-parameter photometers, for example, it is possible to determine alkalinity, chlorine, cyanuric acid or the pH value.

- different selectable parameters
- bluetooth connection
- with free app and software
- exchangeable and lockable cuvette
- LED with different wavelength ranges
- automatic shutdown when inactive

more

The advanced pH meter stands for precision, user-friendliness, and GLP compliance (Good Laboratory Practice). GLP compliance is ensured through automatic data recording and traceable documentation. It allows measurement of pH or redox value and temperature with external sensors.

- Redox measurement (with optional electrode)
- GLP data management
- easy 2, 3, 4, and 5-point calibration
- permanent Measurement Verification (PMV)
- graphical display of measurement history
- data logger

more

The Bluetooth wood moisture tester is easy to use with an Android or iOS device. Up to 44 different types of wood and also other building materials, wood fiber insulation board and chipboard can be checked for their moisture content. The measured value can be up to 150% moisture in relation to the dry matter.

- electrical resistance measurement with temperature compensation
- measuring range for wood, wood fiber insulation, chipboards up to 150 %
- moisture for building material with digit display 11 ... 200 digits
- ram electrode with two pairs of needles, penenetration depth 30 mm / 150 mm
- Bluetooth 4.0


more