| Motors |
|
SSB-Antriebstechnik manufactures electric machines based on all known
technologies. Consistent utilization of the full mounting space available for
electromagnetically active components such as the winding and magnetic circuit
results in electrical machines capable of offering maximum efficiency coupled
with minimal space requirement and extremely low weight. |
|
 |
 |
 |
| Asynchronous machines |
| SSB asynchronous machines for frequency converter
operation are used to implement highly dynamic drive systems. Power: from 0,2
to 760 kW
Speed: up to 2985 max rpm
Torque: up to 2427 Nm |
|
| Synchronous machines |
SSB synchronous machines permit operation both in
constant-frequency systems and on static frequency converters. The speed of
these motors can be varied by changing the feed frequency with control ranges
greater than 1:100.
SSB synchronous machines possess very high synchronous torque levels and
substantial overload capability.
Rated output: from 0,3 to 22 kW
Start-up Torque: from 2 to 220 Nm
Breakdown Torque: from 2.7 to 320 Nm |
|
| Servo drives |
| The brushless SSB servo and hollow-shaft servo drive
systems are designed as standard for operation with servo amplifiers with
threephase power output. This permits the implementation of highly dynamic speed
and torque control circuits, as well as position and speed control over a wide
adjustment range.
Torque: from 1.5 to 250 Nm
Peak Torque: from 6 to 175 Nm |
|
 |
 |
 |
| Direct current machines |
| SSB direct current machines can be used to implement
highly dynamic speed and torque control circuits.
Torque: from 0.5 to 477 Nm
Rated Speed: from 1500 to 3000 rpm |
|
| Positioning drives |
SSB positioning drives are durable threephase motors with
two isolated windings, integrated electromechanical holding brake, external
ventilation and thermal winding protection.
SSB positioning drives can be supplied with a wide range of different motor
characteristics, guaranteeing optimum adjustment even under difficult operating
Output: from 0,025 to 60 kW
Rapid traverse speed: from 2580 to 2950 rpm
Max. breaking Torque: 4 to 540 Nm |
|
| Special drive engineering |
| Alongside the drive engineering expertise offered in our
standard range, we also undertake bespoke electromechanical developments -
specifically engineered solutions to demanding requirements in the field of
drive engineering. |
|
| Gears |
| Alongside its
standard gear range, SSB-Antriebstechnik also produces a wide range of
customer-specific gears designed precisely in line with the specific
application. All SSB gears are dimensioned as a point of principle to ensure a
long life and optimum operational reliability. |
|
 |
 |
 |
| Coaxial gears |
SSB coaxial gears feature the following characteristics:
- Output shaft runs coaxially to the motor shaft
- 1-3 step configuration, with series-connected gear 3-4 step, as double gear 4-5
step
- Base and flange-mounting designs
- Gear housing made of high-grade grey cast iron
- Shafts, wheels and bearings are made of high-grade steels
- The gear wheels are case-hardened >60 HRC, helical geared with ground tooth
flanks
- Completely closed gears, protection rating IP 55
- With the exception of types with single-step series connected gear and
single-step gears, the output and motor shafts are coaxially positioned
Range:
G01: up to 59 Nm Ratio: 5...46
G0: up to 132 Nm Ratio: 2...54
G1: up to 315 Nm Ratio: 2...444
G2: up to 710 Nm Ratio: 2...2090
G3: up to 1250 Nm Ratio: 2...2103
G4: up to 2300 Nm Ratio: 4...10845
G5: up to 4000 Nm Ratio: 27...8486 |
|
| Flat gears |
SSB flat gears feature the following characteristics:
- Output shaft runs coaxially to the motor shaft
- The gears are 2-step, by mounting an additional 1 or 2-step gear, a 3 or
4-step version can be produced
- Gear housing in high-grade grey cast iron
- Extremely high speed reduction ratios can be achieved
- Shafts, wheels and bearings are made of high-grade steel
- All wheels are case-hardened > 60 HRC, with helical gearing and ground
tooth flanks
- The gears are completely closed, protection rating IP 55
The performance spectrum of the standard series covers:
Size Torque levels to [Nm] Transmission ratio i appr.
F01: up to 93 Nm Ratio: 8....70
F0: up to 238 Nm Ratio: 4...649
F1: up to 450 Nm Ratio: 4...688
F2: up to 1000 Nm Ratio: 4...646
F3: up to 1800 Nm Ratio: 5...636
F4: up to 3000 Nm Ratio: 3...402 |
|
| Worm gears |
SSB worm gears feature the following special
characteristics:
- Drive shaft runs at right angles to the motor shaft
- Gear housing in high-grade grey cast iron
- Depending on the required speed reduction ratio, gears are
self-inhibiting
- The worm gear is manufactured from phosphor-bronze
- All wheels are case hardened > 60 HRC, with helical gearing and ground
tooth flanks
- Shafts, wheels and bearings made of high-grade steel
- Gears are completely enclosed, protection rating IP 55
|
|
 |
 |
|
| Helical bevel gears |
SSB helical bevel gears feature the following special
characteristics:
- Output shaft runs at right angles to the motor shaft
- 3-step configuration, with series-connected gear 4 -5 step
- Base and flange-mounting designs
- Gear housing in high-grade grey cast iron
- Shafts, wheels and bearings made of high-grade steel
- All wheels are case hardened > 60 HRC, with helical gearing and ground
tooth flanks
- Gears are completely enclosed, protection rating IP 55
|
|
| Special gears |
- Configuration in line with customer-specific requirements
- Compact designs with high power density
- Versions with characteristics customized for specific applications
- Connection dimensions possible to customer specification
|
|
|
| Converters and
control systems |
|
SSB-Antriebstechnik offers a complete range of converters capable of turning a
rigid power supply into one with variable voltages and/or frequencies. These
devices are essentially designed to provide a controlled energy supply to
electrical machines. As well as the necessary output stages they also feature a
suitable processor for the implementation of complex control circuits. |
|
 |
 |
 |
| Universal converters |
| The universal converters UNITEC 2000 and UNITEC 3000 can
be used to implement all types of threephase drive. The required operating mode
is determined by parameter setting. |
|
| Frequency converters |
| SSB frequency converters are used to implement a wide
range of applications using standard and custom-specific software modules. |
|
| Servo converters |
| SSB servo converters are used to implement a wide range of
applications using standard and custom-specific software modules. |
|
 |
 |
 |
| Power converters for DC machines |
| SSB power converters for DC machines provide a series of
converters for low-loss speed and torque control of DC machines. |
|
| Voltage controllers / Soft start controllers |
| SSB offers a whole range of voltage controllers for
stepless torque control and soft start-up of asynchronous machines adjusted
ideally to the offered drive systems, to address a wide range of drive
requirements. |
|
| System solutions |
| Alongside the drive engineering expertise offered in our
standard range, we offer customer-specific system solutions optimized for
individual applications which are ideal when it comes to solving demanding drive
engineering assignments. |
|
E 
