Spur gears, positioning actuators and pressure-measurement from halstrup-walcher

Positioning technology Due to the wide variety of different models and options, positioning units from halstrup-walcher are eminently suitable for use in machinery and plant construction (packing lines, filling units, printing equipment, wood-processing equipment, metering pumps, valve control) and in medical technology and the pharmaceutical industry.

PSE 21_/23_-8 Positioning system with economic DC motor, drive system, controller and integrated absolute position measuring system,. Machines and stops are reset automatically within minutes, which eliminates rejects due to operator error and significantly reduces downtimes. Date iinterface CANopen/DS 301, Device Net Technical data: DC motor Supply voltage: 24 V DC ± 10% Nominal torque: 1/2 Nm Nominal speed: 40 min -1 at 1 Nm, 20 min -1 at 2 Nm Protection type IP 54 Data interface: CAN Bus, DeviceNet Absolute position detection	PSE 30_-8 Positioning system with controller, gear with a electronically commutated DC motor (brushless) and absolute measuring system. Machines and stops are reset automatically within minutes, which eliminates rejects due to operator error and significantly reduces downtimes. Iinterface CANopen/DS 301, Profibus, Device Net Technical data: With electronically commutated DC-motor (brushless) Supply voltage 24 VDC ± 10 % Nominal torque: 1/2/5 Nm Nominal rated speed: 250 U/min/ 125 U/min/ 40 U/min Positioning range: 256 revolutions Protection class: IP 54 Interface: CAN-Bus/DS 301, Profibus DP, DeviceNet Absolute position measuring technique	PSE 30_/32_-14 Positioning system with controller, gear with a electronically commutated DC motor (brushless) and absolute measuring system. Machines and stops are reset automatically within minutes, which eliminates rejects due to operator error and significantly reduces downtimes. Iinterface CAN-Bus/DS 301, Profibus, Device Net Technical data: With electronically commutated DC-motor (brushless) Supply voltage 24 VDC ± 10 % Nominal torque: 1/2/5 Nm Nominal rated speed: 230 U/min/ 115 U/min/ 40 U/min 170 U/min 68 U/min Positioning range: 256 revolutions Protection class: IP 54 Interface: CAN-Bus/DS 301, Profibus DP, Device Net Absolute position measuring technique	PSE 31_-8 Positioning system with controller, gear with a electronically commutated DC motor (brushless) and absolute measuring system. Machines and stops are reset automatically within minutes, which eliminates rejects due to operator error and significantly reduces downtimes. CAN bus data interface. Technical data: With electronically commutated DC-motor (brushless) Supply voltage 24 VDC ± 10 % Nominal torque: 1/2/5 Nm Nominal rated speed: 230 U/min/ 115 U/min/ 40 U/min Positioning range: 256 revolutions Protection class: IP 54 Interface: CAN-Bus/DS 301, Profibus DP, Device Net Absolute position measuring technique

PSE 31_/33_-14 Positioning system with controller, gear with a electronically commutated DC motor (brushless) and absolute measuring system. Machines and stops are reset automatically within minutes, which eliminates rejects due to operator error and significantly reduces downtimes. Iinterface CANopen/DS 301, Profibus, DeviceNet Technical data: With electronically commutated DC-motor (brushless) Supply voltage: 24 VDC ± 10 % Nominal torque: 1/2/5 Nm Nominal rated speed: 230 U/min/ 115 U/min/ 40 U/min, 170 U/min, 68 U/min Positioning range: 256 revolutions Protection class: IP 54 Interface: CAN-Bus/DS 301, Profibus DP, DeviceNet Absolute position measuring technique	PSE 36_-8 Positioning system in stainless steel housing, horizontal construction, IP 68 protection class, with controller, gear, DC motor (brushless) and absolute measuring system. Simple hollow shaft mounting, no reference runs required, integrated position control, resistant to obstructions, hand brake for raising the holding torque, data interface = CAN-Bus/DS301, Profibus DP, Device Net. Technical data: With electronically commutated DC-motor (brushless) Supply voltage: 24 VDC ± 10 % Nominal torque: 1/2/5 Nm Nominal rated speed: 180 U/min/ 100 U/min/ 35 U/min Positioning range: 256 revolutions Protection class: IP 68 Interface: CAN-Bus/DS 301, Profibus DP, DeviceNet Absolute position measuring technique	PSE 36_/38_-14 Positioning system in stainless steel housing, horizontal construction, IP 68 protection class, with controller, gear, DC motor (brushless) and absolute measuring system. Simple hollow shaft mounting, no reference runs required, integrated position control, resistant to obstructions, hand brake for raising the holding torque, data interface = CAN-Bus/DS301, Profibus DP, DeviceNet. Technical data: With electronically commutated DC-motor (brushless) Supply voltage: 24 VDC ± 10 % Nominal torque: 1/2/5 Nm Nominal rated speed: 180 U/min/ 100 U/min/ 35 U/min 125 U/min 50 U/min Positioning range: 256 revolutions Protection class: IP 68 Interface: CAN-Bus/DS 301, Profibus DP, DeviceNet Absolute position measuring technique	PSE 37_-8 Positioning system in stainless steel housing, longitudinal construction, IP 68 protection class, with controller, gear, DC motor (brushless) and absolute measuring system. Simple hollow shaft mounting, no reference runs required, integrated position control, resistant to obstructions, hand brake for raising the holding torque, data interface = CAN-Bus/DS301, Profibus DP, Device Net. Technical data: With electronically commutated DC-motor (brushless) Supply voltage: 24 VDC ± 10 % Nominal torque: 1/2/5 Nm Nominal rated speed: 180 U/min/ 100 U/min/ 35 U/min Positioning range: 256 revolutions Protection class: IP 68 Interface: CAN-Bus/DS 301, Profibus DP, DeviceNet Absolute position measuring technique

PSE 37_/39_-14 Positioning system in stainless steel housing, longitudinal construction, IP 68 protection class, with controller, gear, DC motor (brushless) and absolute measuring system. Simple hollow shaft mounting, no reference runs required, integrated position control, resistant to obstructions, hand brake for raising the holding torque, data interface = CAN-Bus/DS301, Profibus DP, DeviceNet. Technical data: With electronically commutated DC-motor (brushless) Supply voltage: 24 VDC ± 10 % Nominal torque: 1/2/5 Nm Nominal rated speed: 180 U/min/ 100U/min/ 35 U/min 125 U/min 50 U/min Positioning range: 256 revolutions Protection class: IP 68 Interface: CAN-Bus/DS 301, Profibus DP, DeviceNet Absolute position measuring technique	PSE 37_/39_-8/-14 RD Positioning system in a round, stainless steel housing, V4A design, nominal power output up to 35W, IP 68 protection class, with controller, gear, DC motor (brushless) and absolute position measuring technique. Output shaft with a 10 mm external square shaft or a hollow shaft with adjustable collar; no reference run required; integrated position control; data interface: CAN-Bus/DS301, Profibus DP, DeviceNet. Technical data: With brushless DC motor 24 VDC Supply voltage: ± 10 % galvanic separation between control unit and motor nominal torque: 1/2/5 Nm nominal rated speed: 180 min-1/ 100 min-1/ 125 min-1/ 50 min-1 positioning range: 256 revolutions Output shaft with 10 mm external square shaft 8H9/14H7 hollow shaft with adjustable collar. others available upon request protection class: IP 68 interface: CAN open/DS 301, Profibus, DeviceNet absolute position measuring technique	PSE 34_-14 Positioning system with controller, gear, DC motor (brushless) and absolute measuring system. Simple hollow shaft mounting, manually operated possible, no reference runs required, integrated position control, resistant to obstructions, hand brake for raising the holding torque, joy key operation, data interface = CAN-Bus/DS301, Profibus DP, Device Net. Technical data: With electronically commutated DC-motor (brushless) Supply voltage: 24 VDC ± 10 % Nominal torque: 10/18 Nm Nominal rated speed: 100 U/min/ 60 U/min Positioning range: 256 revolutions Protection class: IP 54 Interface: CAN-Bus/DS 301, Profibus DP, DeviceNet Absolute position measuring technique	PSE 31_-VG-14 Positioning system with a flange-mounted reduction gear, controller, gear, brushless DC motor and absolute measuring system for higher torque requirements. Machines and stops are refit automatically, which eliminates rejects due to operator error and significantly reduces downtimes. Data interface: CAN-Bus/DS 301, Profibus, DeviceNet. Technical data: With electronically commutated DC-motor (brushless) Supply voltage: 24 VDC ± 10 % Nominal torque: 10/18 Nm Nominal rated speed: 100 U/min/ 60 U/min Positioning range: 256 revolutions Protection class: IP 54 Interface: CAN-Bus/DS 301, Profibus DP, DeviceNet Absolute position measuring technique

PSE 42_ Positioning system with control unit, stepping motor, gear and absolute measurement system. Automatic re-fitting within minutes, no wastage as a result of operating errors, considerable reduction of downtimes. Technical data: Supply voltage: 24 VDC Nominal torque: 3/10/25 Nm Speed: 75 U/min,22 U/min, 9 U/min Positioning range: Up to 80 revolutions Protection class: IP 54 CAN bus or Profibus interface Absolute position measuring technique	PSE 43_ Positioning system with control unit, motor, gear and absolute measurement system. Automatic re-fitting within minutes, no wastage as a result of operating errors, considerable reduction of downtimes. Technical data: Supply voltage: 24 VDC Nominal torque: 3/10/25 Nm Speed: 75 U/min,22 U/min,9 U/min Positioning range: Up to 80 revolutions Protection class: IP 54 CAN bus or Profibus interface Absolute position measuring technique	PSE 200 Actuator and position control loop for the positioning of rotating machine parts. Technical data: Supply voltage: 24 VDC Set-point value: 0 - 10 V optional 0(4) - 20 mA Analog output: 0 - 10 V optional 0/4 - 20 mA Control time: 0.5,3 7.5 ...60 s/90° Nominal torque: 1, 5, ...10 Nm Control range: max. 20 revolutions Protection class: IP 55	PSE 272 Positioning system. Complete unit consisting of actuator and position control loop. Simple set-point value, can be connected directly to SPC. Control range up to 20 revolutions. Protection class IP 65. Technical data: Control time sec per 90° 0.25, to 2 Nominal torque: max. 5 Nm Supply voltage: VDC Power input: 15 VA Set-point value: 0 - 10 V (optional 0/4-20 mA)

PSE 100 Positioning system with torque of up to 10 Nm, consisting of actuator and position control loop for the positioning of rotating machine parts. Technical data: Supply voltage: 24 VAC / 230 VAC Set-point value: 0 - 10 V optional 0/4 - 20 mA Analog output: 0 - 10 V optional 0/4 - 20 mA Control time: 7.5....60 s/90° Nominal torque: max. 10 Nm Control range: max. 20 revolutions Protection class: IP 55	PSE 172 Positioning system. Complete unit consisting of actuator and position control loop. Simple set-point value, can be connected directly to SPC. Control range up to 20 revolutions. Protection class IP 65. Technical data: Control time sec per 90° 1 to 7.5 Nominal torque: max. 3.5 Nm Supply voltage: VAC Set-point value: 0 - 10 V (optional 0/4-20 mA)	Linear positioning system: LPE 72 Linear positioning system. Complete unit consisting of spindle drive and position control loop. Simple set-point value, can be connected directly to SPC, high control speed, protection class IP 64. Technical data: Lifting speed: 250 - 4000 mm/min Lifting capacity/length of stroke: 100N/120 /mm Supply voltage: 24 VDC Set-point value: 0 - 10 V (optional 0/4-20mA)	Linear positioning system: LPE 4310 C The LPE 4310 C linear positioning system with stepping motor, controller, gear and absolute measuring system. Very high degree of positioning accuracy. Automatic changing over within minutes, elimination of rejects due to operator error and a significant reduction in downtimes. CAN bus interface. Technical data: stepping motor supply voltage: 24 VDC nominal positioning power: 1000 N upstroke speed: 20 mm/s upstroke: 75 mm positioning accuracy: ± 0.05 mm protection class: IP 54 interface: CAN bus data interface absolute measuring system

Drive technology Due to the wide variety of different models and options, gears from halstrup-walcher are eminently suitable for use in building installations (e.g. for ventilation, exhaust air and flue gas dampers, for valves, window openers), in medical technology (e.g. for dialysis pumps, X-ray equipment, recorders for ECG/EEG equipment), for optical and electronic equipment (e.g. for scanners, measuring systems for ticket and card readers), in machinery and plant construction (ink zone adjustment, limit-stop control, vending machines, metering pumps, filler units).

Actuator: ST 120 KG Gear unit with synchronous or DC motor, limit on the angle of rotation and positional feedback via potentiometer. Technical data: With AC motor: Control time: 7.5.....60 s/90° Nominal torque: 2,5....10 Nm Control range: max. 2 revolutions With DC motor: Control time: 2,5...20 s/90° Nominal torque: 2,5....10 Nm Control range: max. 2 revolutions	Actuator: BK 80 Spur gear with closed aluminium housing, low-noise plate gear Technical data: Nominal torque: 8 Nm Radial/axial load: 60N/40N gear ratios: of 37.5: 1 up to 1000:1 max. diameter of motor shaft: 7 mm. IP 54	Spur gear: N 40 V Spur gear. Plate gear with low gear backlash, carbonised and mounted in a slide bearing output shaft (also fitted with ball bearings as an option). Technical data: With AC-Motor: Output speed: 15.....0.5 rpm Nominal torque: 100 Ncm max. Radial/axial load: 30N/20N With DC-Motor: Output speed: 120.....4 rpm Nominal torque: 100 Ncm max. Radial/axial load: 30N/20N	Spur gear: N 72 Spur wheel, compact design with a variety of transmissions, can be used with motors from various manufacturers. Technical data: Output speed: 10....0,5 rpm Nominal torque: 1.....5 Nm Supply voltage: 24 VAC, 230 VAC

Spur gear: N64 V 30 Spur gear. Plate gear with low gear backlash, carbonised and mounted in a slide bearing output shaft (also fitted with ball bearings as an option). Technical data: With the AC motor: Output speed: 0.5... 60 rpm Nominal torque: 300 Ncm...60 Ncm Radial/axial load: 30N/20N With the DC motor: Output speed: from 2.. 160 rpm Nominal torque:300 Ncm...100 Ncm Radial/axial load: 30N/20N	Linear drives: LA 68 Linear drive. Drive with selection of different lifting speeds. Length of stroke is limited by position switches. Technical data: With AC motor: Lifting speed: 192.....46 mm/min Lifting capacity: 200.....500 N Length of stroke: max. 200 mm With DC motor: Lifting speed: 1000.....350 mm/min Lifting capacity: 200.....500 N Length of stroke: max. 200 mm	Spur gear: N 100 Spur gear, plate gear with low gear backlash, carbonised and mounted in a slide bearing output shaft (also fitted with ball bearings as an option). Technical data: With AC motor: Output speed: 4.....0,25 rpm Nominal torque: 6...... 20 Nm Radial/axial load: 80N/60N With DC motor: Output speed: 30.....2 rpm Nominal torque: 6....20 Nm Radial/axial load: 80N/60N

Pressure measuring technology Differential-pressure transducers and calibration equipment for air and non-aggressive gases. Due to the wide variety of different models and options, differential-pressure transducers and calibration equipment from halstrup-walcher are eminently suitable for use in ventilation and air-conditioning technology, for filter control, in clean rooms and medical technology, in mechanical engineering and as service equipment for assembly and maintenance work. The pressure transducer and calibration equipment are available with calibration record or DKD certificate.

Differential pressure transducer: PUC 24 Process monitoring device for clean rooms. Room pressure measurement with inputs for humidity and temperature sensors. Measured values are sent to the control module via a Profibus interface. Technical data: Measurement range: freely scalable within ± 100 Pa or ± 250 Pa Retest precision: 0.1% Profibus DP interface (optional) Automatic zero-point calibration Alarm contacts Input signal for: temperature module: adjustable between 0-10 V / 0/4-20 mA humidity module: adjustable between 0-10 V / 0/4-20 mA	Differential pressure transducer: PUC 28 Process monitoring device for measuring room pressure in clean rooms. The device is equipped with a smooth plastic exterior and additional input ports for connecting external temperature and humidity sensors. The device communicates with a master control via profibus (optional). Technical data: Measurement range: ±100 Pa measurement uncertainty 0.3Pa +0.5% of max. value Input signal for temperature module: adjustable between 0-10 V / 0/4-20 mA Input signal for humidity module: adjustable between 0-10 V / 0/4-20 mA Data interfaces: profibus DP (optional), RS 232 (optional) Zero-point calibration cycle Alarm contacts	Differential pressure transducer: P 29 Differential pressure transmitter with TÜV certification for use with combustible gases, freely scaleable with a measuring range of 250 Pa to 100 kPa, high repeatability and precision due to automatic zero balance; available with calibration protocol or DAkkS/DKD certificate. Technical data: Measuring ranges: 250 Pa to 100 kPa freely scaleable between 10 and 100 % high accuracy and long-term stability no zero point drift due to automatic zero balance, low hysteresis, good overload relief Configurable time constants and output characteristics (root extracted/linear) Protection type IP 65 Optional rail mounting Option: LC display	Differential pressure transducer: P 26 Differential pressure transducer; freely scalable within a range of ± 10 Pa to ±100 kPa; automatic zero-point calibration provides excellent reproducibility and precision; optional RS 232 C interface; configurator available as an accessory. Technical data: measurement ranges: ±10 Pa to ±100 kPa freely scalable from 10 to 100% high level of accuracy and long-term stability automatic zero-point calibration eliminates zero-point drift low level of hysteresis high level of overpressure protection time constants and output characteristics can be configured (root-extracted / linear) can be mounted on top-hat rails Options: contact points with adjustable switching outputs, RS 232 interface

Differential pressure transducer: P82 R Measuring transducer with square root-extracted output characteristic, which is thus suitable for the direct measurement of the volumetric flow rate via measuring orifice, concentric nozzle, flow grid, etc. Technical data: Measuring ranges: from 0 - 100 Pa to 0 - 20 kPa Linearity: ± 1 % Output signals: 0 - 10 V, 0 - 20 mA, 4 - 20 mA Supply voltages: 230 VAC, 115 VAC,24 VDC, 24 VAC Time constants: 1,2,5 s optional Medium: air, all non-aggressive gases. Can also be calibrated in other units of measurement, e.g. mbar, mmWs, psi, m3/h, m/s etc.	Differential pressure transducer: PUE 94 Measuring transducer with high overload capacity for measurements that could be impaired by pressure fluctuations. Technical data: High sensitivity, high precision and long-term stability Low zero drift Hysteresis and temperature-dependence Measuring ranges: from 0 - 250 Pa to 0 - 30 kPa Linearity: ± 1, optional ± 0.5% Output signals: 0 - 10 V, 0 - 20 mA, 4 - 20 mA Supply voltage: 24 V DC, 24 V AC, 230 V DC Medium: air, all non-aggressive gases	Differential pressure transducer: PU/PI Measuring transducer with high precision and long-term stability for measuring the pressure in air-conditioning and ventilation units, for monitoring filling levels and for filter control, etc. Technical data: Measuring ranges: from ± 50 Pa to ± 100 kPa Linearity: ± 1 %, optional ± 0.5 ± 0.2 % Output signals: 0 - 10 V, 0 - 20 mA, 4 - 20 mA Supply voltages: 24 VAC, 24 VDC, 230 VAC Time constants (optional): 1,2,5 s Medium: air, all non-aggressive gases	Differential pressure transducer: PIZ Measuring transducer with two-conductor system 10 - 32 V, with high precision and long-term stability for measuring the pressure in air-conditioning and ventilation units, for monitoring filling levels and for filter control. Technical data: Measuring ranges: from ± 50 Pa to ± 100 kPa Linearity: ± 1 %, optional ± 0.5 ± 0.2 % Output signals: 4 - 20 mA Supply voltage: 10 - 32 VDC Time constants (optional): 1,2,5 s Medium: air, all non-aggressive gases

Differential pressure transducer: PS 10 Measuring transducer preferably used as built-in device in air-conditioning and ventilation technology. Technical data: Measuring ranges: from ± 250 Pa to ± 100 kPa Linearity: ± 2 % Output signals: 0-10 V, 0-20 mA, 4-20 mA Supply voltages: 24 VAC, 24 VDC, 230 VAC Medium: air, all non-aggressive gases	Differential pressure transducer: PK 15 Measuring transducer with analog output for applications requiring an optional or acoustic signal as warning message. Technical data: Measuring ranges: ± 50 Pa to ± 100 kPa Linearity: ± 1 %, optional ± 0.5 ± 0.2 % Output signals: 0-10 V, 0-20 mA, 4-20 mA Supply voltages: 24 VAC, 24 VDC, 230 VAC Time constants: 20 ms, 1,2,5 s Medium: air, all non-aggressive gases	Differential pressure transducer: PS 27 Differential pressure transducer for simple air-conditioning and ventilation applications, highly sensitivity, excellent long-term stability, suitable for mounting on top-hat rails. Technical data: High level of sensitivity High level of accuracy and long-term stability Measuring ranges: ± 100 Pa to ± 100 kPa Linearity: 2 % v.E. Very little zero-point drift: 0,1 % /K Very little hysteresis: 0,1 % / K Overload protection: 4x for measurement ranges <= 30 kPa 12x for measurement ranges <= 20 kPa Output signals: 0 - 10 V, 0/4 ...20 mA Supply voltage: 24 V AC/DC ( no galvanic separation) 15...32 VDC (two wire system) Top-hat rail mounting Medium: air, all non-aggressive gases.	Differential pressure transducer: REG 21 Pressure controller, design in panel housing with large, bright LE-Display, with 2 adjustable relay outputs, which allows to realize a 2 or 3 step controller. In addition to the relay output there is an analogue output. Technical data: Measuring ranges: 0 - 50 Pa to 0 - 100 kPa Linearity: ± 1 %, optional ± 0.5 % Output signals: 0-10 V, 0-20 mA, 4-20 mA Supply voltages: 230 VAC, 24 VAC, 24 VDC Medium: air, all non-aggressive gases

Digital manometer: EMA 200 Portable, battery-powered, digital pressure gauge for assembly and maintenance tasks performed by service technicians in the heating, air-conditioning and ventilation industries. For measuring fireplace drafts, volume flow, etc., and for monitoring filters, etc. Measurement ranges up to 0 - 200 kPa. Technical data: Measuring ranges: from 0 -200 Pa to 0-20 kPa Can also be calibrated in other units Linearity: 0,5 % v.E. Stores min. and max. value Option: 0 - 2 V Easy to operate Medium: Air, all non -aggressive gases	Digital manometer: EMA 84 Portable, battery-operated measuring device for assembly and maintenance work in customer services for heating, air-conditioning and ventilation units, for measuring the chimney draught, the wind pressure, for filter control, for laboratory work, etc. Measuring range up to 100 kPa. Technical data: Measuring: 0-100 Pa to 0-100 kPa Can also be calibrated in other units of measurement Linearity: ± 1.0 %, optional ± 0.5 %, ± 0.2 % Analog output: 0-1 V (optional) Ease of operation Adjustable response times Accuracy of up to ± 0. 2 % Battery-operated Medium: air and all non-aggressive gases	Callibration equipment: KAL 84 In the case of a variable volume, a hand pump (optional) can also be connected. Use in accordance with the Medical Devices Directive, Measurement Control Technical data: Measuring ranges: 0-100.0 Pa to 0-100.0 kPa Good linearity: ± 1.0 % optional ± 0.5 %, ± 0.2 % Analog output: 0-1 V 4-figure display Internal air compression Battery-operated (accumulator) Medium: air and all non-aggressive gases	Callibration equipment: KAL 100 Portable, calibration device. A combination of pressure transducer and pressure gauge. The desired pressure is displayed digitally. Technical data: Measuring ranges: from 0-100 Pa to 0-100.0 kPa Linearity: up to 100 Pa ± 0,5 % up to 1 kPa 0,1 % LC- display with 2x20 characters Internal air compression Automatic zero balancing Overload protection operation software Optional: power supply and measuring input 24 VDC Optional: USB Interface Optional: Lithium-Ionen Accumulator: Simple-to-operate calibration device with very good cost/benefit ratio Medium: air all non-aggressive gases

Callibration equipment: KAL 200 Portable calibration device with integrated pressure generator. Combination pressure transducer and pressure gauge. Technical data: Measurement ranges: from 0 - 100 Pa to 0 -100 kPa Linearity: up to 100 Pa ± 0,3 % up to 1 kPa 0,1 % LCD with 2 x 20 characters Automatic zero-point calibration Overload protection operation software USB interface power supply and measuring input: 24 VDC Optional: Lithium-Ionen Accumulator Easy-to-operate calibration device with an excellent price/performance ratio Medium: Air, all inert gases	Absolute pressure transducer: AD 1000 Absolute pressure transducer is suitable for measuring or controlling air pressure or absolute pressure. Technical data: Measuring ranges: 0-120 kPa, others available on request Supply voltages: 24 VAC, 230 VAC, 115 VAC, 24 VDC. Linearity: +/- 1 % Output signals: 0-10 V, 0-20 mA, 4-20 mA Can also be calibrated in other units of measurement	Absolute pressure transducer: BA 1000 Electronic barometer is suitable for displaying the barometric air pressure. Technical data: Measuring ranges: 0 - 120 kPa, others available on request Supply voltage: 24 VAC, 230 VAC, 115 VAC, 24 VDC. Linearity: +/- 1 % Output signals: 0-10 V, 0-20 mA, 4-20 mA Can also be calibrated in other units of measurement	Absolute pressure transducer: BA 90 Digital manometer is suitable for installation in control panels to display the barometric air pressure. Technical data: Measuring ranges: 913.3 to 1113.3 kPa Supply voltages: 24 VAC, 230 VAC, 115 VAC, 24 VDC, 12 VDC Linearity: +/- 0.4 kPa, +/-1 digit Output signals: -2 ..+2 V, 0-20 mA, 4-20 mA

EXPO21XX Online Trade Fair		Navigation : EXPO21XX.com > MOTION 21XX > Complete electric drive solutions > halstrup-walcher