Horizontal baler type AVOS 1810 B5

Powerful and economic for big challenges

The horizontal baler type AVOS 1810 B5 is the right choice for compacting large waste amounts. The press ram is guided either on plastic rails or steel rollers. When pressing fine grain or highly expansive materials, the press can be equipped with a cross binding system. In combination with the optimized cutting system "OptiCut" and the use of one or two most energy-efficient, high-performance hydraulic pumps, this baler offers an impressive spectrum for applications with maximum throughputs. Furthermore, the sophisticated key transfer system (optional) guarantees the highest level of operation safety.

Download Product data sheet

Installation of an AVOS 1810 B5-90/100
Press ram for cross binding

The fully automated horizontal baler AVOS 1810 B5 is perfectly suitable to compact cardboard, paper, plastics, and other recyclable materials. State of the art technology according to the C standard for horizontal balers published in 2013 (DIN EN 16252).

  • The frame of the machine consists of a solid welded construction and is provided for fastening on the floor with dowels.
  • Rapid motion/power speed control system as well as an automatic speed adaptation, depending on the necessary pressing power, for the increase of the throughput capacity.
  • Cutting knives on the force plate and on the counter plate for cutting off the overhanging material in the hopper section. Temper of the knives: 56 + 4 HRC
  • Cutting edge stamper, fully automatic hydraulically operated; power: 196 kN.
  • Press ram guiding with low-maintenance plastic guides, highly wear-resisting, and indifferent to dust.
  • Force plate channel laterally and below made of 15 mm Hardox 400 sheet steel for longevity.
  • Screw press bottom made of wear-resistant 15 mm Hardox 400 sheet steel for easy replacement.
  • Press ram cover for continuous feeding.
  • Three-sided adjustment of press channel, regulation depending on pressing power, to achieve maximum bale weights.
  • Automatic binding with drill fingers made of highly wear-resisting NAXTRA material as well as separate wire cutting knife guarantees a safe binding of bales.
    Wire diameters available:               3.1 mm / 3.4 mm / 3.8 mm
  • Free programmable PLC, Siemens Simatic S 7, including switching and control elements.
  • Potential free contacts for emergency stop, automatic mode, general fault, overfill protection, material feed conveyor belt.
  • Integration of external emergency stop in the baler control.
  • Electrically controlled bale length measuring system.
  • Touchscreen display: Size 12.1’’, type Schneider Electric, HMIGTO 6310, 800 x 600 pixel (SVGA), to operate and control the machine, incl. monitoring of performance data. Individual programes for different materials can be set up individually.
  • Heating of the control cabinet.
  • Photo cells inside the hopper of the baler for the press stroke control and as overcharge protection.
  • Capacity controlled, power saving press ram drive via axial piston pump, Type Rexroth, operating pressure 320 bar.
  • First equipment of hydraulic oil type HLP46, capacity: 2,000 l, with oil level switch that switches off the machine in case of an excessively low oil level.
  • Separate heating, cooling, and filter circuit for the hydraulic oil, oil filtration with 3µm filter.
  • Heating capacity: approx. 7.5 kW
    Cooling capacity: approx. 28 kW with 100 l/min.

  • Hydraulic block with bolt-fitted valves mounted onto the hydraulic block, easily accessible for maintenance.
  • Proportional valve technology for a for smooth and energy-saving system operation.
Description Data

Dimensions:
(L x W x H)

11,200 x 2,400 x 3,900 mm

Hopper cross section:
(L x W)
1,800 x 1,000 mm
Size of bale (W x H):
(adjustable length)
1,100 x 750 mm
Belt connection: alternatively on the left or on the right
Bale weight: up to 700 kg, depending on model, bale length and on the pressed material
Binding: 5-fold vertical
Binding wire: annealed, oiled wire according to DIN 177 (not part of our scope of delivery)
Drive capacity: 55/2 x 45/2 x 55 kW (depending on model)
Press force: 800/1,000 kN (depending on model)
Throughput capacity: see data sheet AVOS 1810 B5
  • Cross binding:
    Fully automated, for safe binding of small-grained and expansive materials. Binding is effected 5-fold vertical and 3-fold horizontal.
  • Feeding chute:
    To connect a conveyor belt, for the automatic feed.
  • Bale slide:
    1.2 x 4.0 m
  • Special press ram
    For pressing scrap, residual waste, wooden boxes etc. There are no openings inside the ram where pressed material can get jammed or emerge. The slots are only released for binding the bale. The press-ram is patented.
  • Press ram guiding
    Press ram guiding with 6 piece-steel rollers on Hardox rails, highly wear resisting, and indifferent to dust.
  • Material re-holder:
    To optimize the pressing process, for highly expanding material, as, for example foil, PET-bottles etc. The re-holders (1 set = 4 pieces) are fitted flexibly in order to guarantee a safe pressing.
  • Wire end control (for top and bottom wire):
    Fully automatic, i.e. with on-screen message “end of wire” the press stops.
  • Wire coil holder:
    For automatic binding, to take up 10 pieces of 400 kg wire coils.
  • Wire stock table:
    For automatic binding, for space-saving keeping of 5 pieces of 400 kg wire coil holders above the bale slide.
  • Binding wire (10 x 400 kg):
    Annealed and oiled binding wire with a diameter of 3.1 mm (according to DIN 177) for binding of bales.
    1 set = 10 coils à 400 kg.
  • Mechanical crimping pliers incl. aluminum clamps:
    To connect new, complete wire coils. The connection is effected by aluminum clamps (1,000 pieces included).
  • Large display:
    Installed on top of the lance unit to indicate the length of the bale.
  • Maintenance platform:
    Incl. EMERGENCY-STOP switch to access the feeding hopper
  • Remote access:
    Through an industrial router in connection with an M2M SIM-card, an interface is created with the control unit of the machine so that the inputs and outputs of the SPS can be displayed in an internet portal. Running costs according to tariff or by network cable provided locally.
  • Profibus connection:
    Electrical switching cabinet design with Profibus-compatible PLC incl. DP/DP coupler, for communication between devices from different manufacturers with no particular interface requirements
  • Perforator type P-1800, movable:
    Screwed on a driveable unit for perforating PET-bottles from 0.33 up to 2 l.
    The perforator is a solid welded sectional steel construction and, on all sides, equipped with sheet metal sheathing.
    By means of a moveable unit, the perforation can be driven into and out of the hopper of the baler.
    The perforator roller is equipped with steel nails.
    Both rollers are electric motor driven and controlled from the horizontal baler (drive capacity = 2 x 3 kW).
  • Ruffler:
    Electric motor driven, in and out swivelling; drive capacity: 11 kW.
  • Feeding and inclining conveyor belt:
    AVERMANN belts are specified and manufactured individually according to the respective application. These belts are produced in modular design by efficient laser-cutting machines and are therefore length-adjustable or extendable at any time. By using high-grade belts (i.e. oil and grease resistant), bulky goods can be transported safely.
    To feed the horizontal baler, designed as chain conveyor type KGF.
    The base frame is a solid welded torsion reinforced steel welding construction for fastening by dowels.
    The transport belt consists of drive chain conveyors (arranged on both sides) according to DIN 8165, transversal beams, and the conveyor belt on it.
    The conveyor belt is designed as a smooth rubber belt with a double insert. The chain conveyor is equipped with emergency trip wires and drip-feed lubricators. In the transfer area there is an emergency delete, too.
    T-protections as labyrinth-sealing on both sides (on the left and on the right) are vulcanized over the complete length on the top of the belt.
  • Pit cover plates for the chain conveyor:
    In the field of the horizontal belt, particularly solid design, accessible by floor conveyors.
  • Feed rear panel:
    Made of solid steel panel, mountable opposing to the feed side. The feed rear panel prevents an ‘over shifting’ of the material over the belt width.
    Length: 6 m
    Height: 1 m
  • Personal protection system:
    An antenna module is mounted above the conveyor belt in front of the filling opening of the baler. The magnetic field of this antenna module monitors the entire length of the conveyor belt. Individuals under protection wear a so-called personal protection module on their clothing or on their wrist.
    If a person wearing such a module now enters the field under magnetic monitoring, it will be detected by the system and the entire plant will automatically and immediately shut down.
    The personal protection system consists of:
    Antenna module
    Evaluation module
    Self-test module
    PSM personal protection module (wristband version)
    PSM test device
    Additional wristbands are charged separately.
    Note: 
    A personal protection system is compulsory in accordance with DIN EN 16252:2013-03 for underfloor feeding conveyor systems.
    Exception: The conveyor system control device is not self-supporting and is arranged in such a way that the operator can easily see the danger zone.
Description Data
Belt guiding:

6,000 mm, 0° horizontal

9,000 mm, 32° increasing

1,000 mm, -10° declining

Conveyor width net: 1,800 mm
Feed height: -500 mm
Length of belt: 16,000 mm
Height of side guiding: 800 mm
Height of attachments: 50 mm
Attachment distance: 750 mm
Motor rating: 7.5 kW

All data are approximate values subject to constructive finalization.

All specifications are approximate values and the final, constructive determination reserved.

  • Convenient handling: Extremely large feeding hopper
  • Powerful: Suitable to compact very large amounts of waste and recyclable materials
  • Reliable: Proven technology from more than 40 years of experience
  • Avermann special press ram to compact "difficult" materials
  • Optimized cutting system "OptiCut" 
  • Feeding conveyor for continuous filling
  • Monitoring of wire breakage and wire end to control the binding wires
  • Cross binding
  • Press ram guided on plastic rails or steel rollers

RAL 1003

colorScale

RAL 2000

colorScale

RAL 3001

colorScale

RAL 3020

colorScale

RAL 5005

colorScale

RAL 5007

colorScale

RAL 5010

colorScale

RAL 5015

colorScale

RAL 5017

colorScale

RAL 6002

colorScale

RAL 6018

colorScale

RAL 6024

colorScale

RAL 7016

colorScale

RAL 7032

colorScale

RAL 7038

colorScale

RAL 9002

colorScale

Other RAL-colors available on request at additional cost.

Technical data

AVOS 1810 B5-55/80

AVOS 1810 B5-90/80

AVOS 1810 B5-90/100

AVOS 1810 B5-110/100

Machine length

11,200 mm

11,200 mm

11,200 mm

11,200 mm

Machine width

2,400 mm

2,400 mm

2,400 mm

2,400 mm

Machine height

3,900 mm

3,900 mm

3,900 mm

3,900 mm

Feeding hopper cross section

1,800 x 1,000 mm

1,800 x 1,000 mm

1,800 x 1,000 mm

1,800 x 1,000 mm

Dead weight approx.

26,000 kg

27,000 kg

28,000 kg

28,000 kg

Bale size (WxH)

1,100 x 750 mm

1,100 x 750 mm

1,100 x 750 mm

1,100 x 750 mm

Bale weight* up-to

650 kg

650 kg

700 kg

700 kg

Channel adjustment

3-sided, automatic

3-sided, automatic

3-sided, automatic

3-sided, automatic

Cycle time

20.4 s

10.2 s

12.5 s

12.5 s

Idle speed capacity (theoretical) 

238 m3/h

476 m3/h

388 m3/h

388 m3/h

Throughput** 35 kg/m3 (cardboard)

5.0 t/h

12.5 t/h

12.1 t/h

12.5 t/h

Throughput** 60 kg/m3 (cardboard, paper)

 8.5 t/h

20.0 t/h

16.0 t/h

17.5 t/h

Throughput** 100 kg/m3 (newspaper)

14.2 t/h

28.5 t/h

23.2 t/h

26.2 t/h

Specific press force

97.0 N/cm2

97.0 N/cm2

121.2 N/cm2

121.2 N/cm2

Drive power

 55 kW

2 x 45 kW

2 x 45 kW

2 x 55 kW

Press force

800 kN

800 kN

1,000 kN

1,000 kN

* depending on bale length and material, ** relating to bulk weight

  • Bale length: Adjustable 
  • Binding: 5-fold vertical 
  • Optional with cross-binding: 5-fold vertical, 3-fold horizontal
  • Electricity: 3 x 400 V, N, PE/50 Hz

Horizontal baler type AVOS 1810 BRK-110/100

High-efficiency horizontal baler with 1000 kN press force and cross-binding

Binding with plastic wire

The binding on an Avermann horizontal baler can be converted from steel wire to plastic wire in less than 2 hours. Ideal if the bales are intended for incineration.

Find out more about our products

Are you looking for advice or do you have a question specifically about this product? Feel free to get in touch with your contact person directly.

Avermann
Maschinenfabrik GmbH & Co. KG

Lengericher Landstraße 35
49078 Osnabrück
Germany

 

Contact us