Navigation : EXPO21XX > AUTOMATION 21XX > H41: Factory Equipment > Lindner-Recyclingtech
Videos
Loading the player ...
  • Offer Profile
  • DEVELOPING AND MANUFACTURING THE MOST RELIABLE AND PRODUCTIVE SHREDDING SYSTEMS
    The Lindner product portfolio ranges from stationary and mobile shredders for waste management through to complete systems for plastics recycling and the production of SRF/RDF fuels. We also design and execute large projects on request. At our three modern production sites in Austria, we manufacture high-end shredders and system components that are used in over 70 countries worldwide.
    • IN-HOUSE R&D
    • MECHANICAL ENGINEERING AND MACHINE WELDING
    • ELECTRONIC COMPONENT DEVELOPMENT
    • IN-HOUSE PROJECT ENGINEERING  
Product Portfolio
  • SYSTEM SOLUTIONS

      • ALTERNATIVE FUELS

          • SRF FOR MAINBURNERS

          • MULTI-STEP PROCESSING OF PREMIUM SOLID RECOVERED FUELS

            Multi-step production of a product with high calorific value - premium SRF (solid recovered fuel) for energy recovery - from muniucipal, commercial and industrial waste.

            PRIMARY SHREDDING
            The process starts with untreated waste from households, commerce and industries being fed – often via wheel loaders, diggers or dosing conveyors – into the primary shredder. The aim is to obtain homogeneous, sortable material ready for the next step in the process.

            MAGNETIC SEPARATION OF FERROUS METALS
            In the second step, a magnet fitted above the conveyor belt is used to securely extract ferromagnetic parts such as scrap iron and other ferrous scrap metal. Ferrous scrap metal in premium solid recovered fuels is said to spoil its quality. Once separated, it can be recycled in line with the circular economy concept.

            SCREENING
            In the third step, the pre-shredded material – now free from any ferrous metals – arrives in a continuous stream of material. The fine particles that are undesirable in SRF but that are often found in the input material are screened at this point. The screening technology can be selected and matched to your exact requirements. Common equipment includes drum screens, strainers, vibrating screens or disc screens. Depending on your requirements, it is possible to extract different fractions in this process stage such as fines of <10 mm and oversized fractions to obtain high-quality, medium-particle solid recovered fuel.

            HEAVY FRACTION SEPARATION
            Heavy fractions might cause increased wear or stand still in the secondary shredding process, that is the reason why such fractions are sorted out. The material stream is fed continuously into a separator where it is hit with an air current while it is in free fall. In this way, light materials are transported by air to the conveyor belt, whereas heavy materials fall to the ground to be discharged. Thanks to the circulating air, hardly any fresh air is needed.

            SECONDARY (FINE) SHREDDING/GRANULATION
            In the final stage of the process, the material is shredded a second time in a process called fine shredding or granulation. The material that is now free from foreign matter, heavy fractions and ferrous metal and fed into one or more secondary shredders depending on the system’s throughput capacity. The output is then known as the final product or premium solid recovered fuel (SRF). Systems typically generate up to 40 tons of final SRF per hour – and that 24 hours a day.

            SRF FOR MAIN BURNERS
            Shredding of municipal, commercial and industrial waste for incineration with energy recovery in the main burner

            Solid Recovered Fuels (SRF) are mostly used in the main burners of rotary kilns and are categorised as solid alternative fuels. The main burner needs fuels that are easily flammable and burn in a way that high material temperatures can be achieved in the kiln’s sintering zone; these are necessary to form the desired clinker minerals (approx. 1,450 °C). For that to happen, the flame has to reach an operation temperature of approx. 2,000 °C. It is therefore vital that the SRF is composed of particles that have been cut perfectly.

            The SRF must be free of foreign matter (e.g. metals, stones or glass) which might cause feeding problems or issues with the clinker quality. With perfectly coordinated processes, Linder high-end primary and secondary shredders, and double extraction of foreign matter, extremely reliable and robust SRF processing with minimum maintenance is guaranteed. Featuring some of the highest throughput rates on the market and ideal output quality, Lindner’s machines also boast surprisingly low energy consumption.


            MATERIALS:

            • MSW
            • BULKY WASTE
            • C&I WASTE
            • REJECTS
          • SRF FOR CALCINERS

          • SINGLE-STAGE PROCESSING OF SOLID RECOVERED FUELS

            Efficient production of RDF for incineration with energy recovery in cement kilns/calciners or as fluidised bed.

            ONE-STEP SHREDDING
            In one-step shredding, the focus is on the shredder as a single-step solution. Untreated waste from households, commerce and industries is mostly fed into the primary shredder directly via wheel loaders, diggers or dosing hoppers with the aim of obtaining homogeneous, sortable material in a single step.

            CONVEYING
            The shredded material continuously trickles out of the base of the shredder. A stationary conveyor belt is conveniently located immediately underneath to transport the product. The ideal choice here is a profiled conveyor belt operated by the Lindner Shredder or the control room.

            METAL SEPARATION
            Optionally, a permanent magnet can be fitted above the conveyor belt to securely extract ferromagnetic parts such as scrap iron and other ferrous scrap metal. Ferrous scrap metal in premium solid recovered fuels is said to spoil its quality. Once separated, it can be recycled in line with the circular economy concept.

            REFUSE-DERIVED FUELS FOR CALCINERS

            Shredding of municipal, commercial and industrial waste for incineration with energy recovery in the calciner

            If you want efficient plants for turning municipal, commercial and industrial waste into fuel, you first have to define the end product. Especially in the single-stage production of fluidised bed fractions for incineration with energy recovery in cement-kilns/calciners, it is vital that the shredding systems work extremely robustly and reliably – and mostly around the clock. The calcinator accepts lower-grade fuels with regard to particle size and calorific value. Unlike in the rotary kiln’s sintering zone, much lower material temperatures (approx. 800–900 °C) are necessary as the CO2 simply needs to be extracted from the lime.

            A wide range of RDFs can be used depending on the calcinator type. With certain calcinators it is even possible to use entire tyres as fuel; however, most standard calcinators (e.g. inline, separate line and combustion chamber) use shredded refuse-derived fuels. Since there is a wide range of calcinator technologies and types, this table only serves as a guideline.

            MATERIALS:
            • MSW
            • BULKY WASTE
            • C&I WASTE
            • REJECTS

            CEMENT KILN – CALCINER FUEL CHARACTERISTICS

            • Particle size < 80mm
            • Calorific value > 12-16 MJ/kg
            • Density < 250 kg/m3
            • Moisture content < 20%
        • PLASTICS RECYCLING

            • POST CONSUMER PLASTICS RECYCLING

            • POST CONSUMER PLASTICS RECYCLING

              Efficient recycling of post-consumer plastics

              Lindner’s multi-stage processing facility for post-consumer plastic is in a class of its own. Perfectly matched components guarantee high output quality. Robust high-end shredding, washing and drying components ensure smooth 24/7 operation with low maintenance and consistently high throughput. It has never been so easy to guarantee the ideal input for subsequent processes.

              SHREDDING
              Shredding is an essential step in a smooth-running process chain. Untreated plastic waste either in baled or loose form is fed into the machine with wheel loaders or a conveyor belt.
              The output is consistent, the cut precise and 90% of the output will be smaller than 60 mm with an output of up to 5 metric tons per hour.

              PREWASHING AND FOREIGN MATTER SEPARATION
              The requirements for prewashing are clearly defined. Pre-shredded plastics are often heavily contaminated and loaded with foreign matter. The rafter’s well-engineered technology effectively separates abrasive matter and prepares the material for all following processes.

              GRANULATION
              Now free from foreign matter, the material is granulated using a wet granulator that screens the material to the preferred particle size to make recycling particularly efficient.

              PLASTICS SEPARATION
              Categorising plastics according to their specific weight. This step is executed with Lindner Washtech’s gravitator, a machine that combines state-of-the-art features with the tried-and-tested sink-float method. In this process, not only is it important that the output material is homogeneous, but the machine’s construction must also be compact and efficient.

              FRICTION WASHING
              Efficient washing through friction. The Lindner Washtech friction washers clean even the smallest particles very effectively. The machine size can be adjusted to the customer’s specific throughput requirements, achieving rates of up to 4 metric tons per hour. The machine’s screens and paddles are also customisable.

              MECHANICAL AND THERMAL DRYING
              The shredded and washed material is fed into a centrifuge where the plastic flakes are dried in controlled conditions. The resulting centrifugal forces contribute to cleaning and drying the materials. Finally, the material is thermally dried and can subsequently be transferred for extrusion.

              CIRCULAR ECONOMY - PLASTICS AS A RAW MATERIAL

              Processing plastics waste for a resource-saving plastic life cycle concept

              Post-consumer waste is created by consumers, e.g. individuals and households. While in the past plastic waste used to be incinerated, these days it is considered an important raw material. To utilise post-consumer plastics, the aforementioned process is necessary. For recycling purposes, the material must be as clean as possible to prevent damage to machines and pre-empt inferior-quality products.

              Lindner relies on tried-and-tested technology to guarantee high-quality material. The field of post-consumer plastics in particular demands high machine standards since the material might not only contain abrasive matter but also food scraps. The foreign object-resistant shredder and the high-end washing technology solution ensure a homogeneous product ready for extrusion. Manufacturing companies can then turn the resulting lenticular plastic raw materials into the final product.

              END PRODUCT CHARACTERISTICS

              • Particle size < 50 mm
              • Moisture content 5-8%
              • Materials PP, PE, PE-HD, PE-LD, PE-LLD, etc.
            • IN-HOUSE RECYCLING

            • INHOUSE PLASTICS RECYCLING

              Don’t waste it: With our compact solution combining primary shredder and granulator, it has never been so easy to make plastic waste, defective products or off-cuts ready to re-enter the production cycle. Enjoy maximum productivity with our highly efficient, robust and low-maintenance components.

              FEEDING
              In this step, the material is fed into the machine via a conveyor belt. Materials can be supplied to the conveyor belt via a wheel loader or a forklift. To facilitate continuous feeding, our shredders permanently communicate with the conveyor belt and subsequent processes such as granulators or extruders. The metal detection system directly connected to the system control protects subsequent processes. This is necessary to guard the granulator, which is sensitive to foreign matter, and to prevent the high costs caused by downtime.

              SHREDDING
              In the second step, the visually inspected material is shredded. The robust Lindner shredder splits the material into the right output size for subsequent processes. To achieve the best possible throughput the shredder, conveyor and granulator continuously communicate and control the speed and the amount processed.

              GRANULATION
              The material coming from the foreign matter-resistant shredder is fed into the granulator and processed to the required particle form. Rotor speeds of 600 rpm are normal in this process. Due to the high speed, it is necessary for the material to be as perfectly prepared as possible to avoid the granulator malfunctioning.

              GRANULATE COLLECTION
              In this step, the material that has been processed by the granulator to a particle size of 8–10 mm is sucked into containers like big bags or directly transported for further processing.

              PROCESSING WASTE FROM PLASTICS PRODUCTION

              Shredding of plastics waste and rejects ensures efficient recycling

              In-house recycling for efficient production processes – plastics and other production waste are important raw materials in the manufacturing of plastic products. Linder shredders were developed with precisely these requirements in mind. Thanks to an adjustable cutting gap and variable screens, you can customise the particle size to the needs of your subsequent processes.

              Our primary shredders are resistant to foreign objects and are able to shred hard, rigid plastics to a particle size of <10 mm, as is necessary for recycling purposes. Since the material is often bulky and slightly contaminated, it is not possible to feed the material directly into the granulator. That’s were the primary shredder comes in, splitting the materials to protect the granulator or extruder and minimise the costs of downtime.

              IN-HOUSE MATERIAL CHARACTERISTICS

              • Particle size < 10 mm
              • Throughput > 4 t/h
              • Material PP, PE, PE-HD, PE-LD, PE-LLD, etc.
          • WASTE WOOD PROCESSING

              • WASTE WOOD RECYCLING

              • WASTE WOOD PROCESSING FOR RECYCLING

                Excellence in shredding: Lindner’s multi-stage processing solution leaves nothing to be desired. Powerful primary shredders combined with well-engineered separation technology and high-precision Komet secondary shredders ensure not only the perfect output, but also the necessary throughput to keep downstream processes running.

                PRIMARY SHREDDING
                After the wood has been sorted in accordance with the waste wood grades, A1 and A2 waste wood is processed in the first shredder. This slow-speed shredding system shreds pallets, chipboard, demolition and other partially bulky wooden parts with the aim of creating homogenous, well-broken-down material to subsequently separate nails and other metal parts from the material.

                MAGNETIC SEPARATION OF FERROUS METALS
                In the second step, a permanent magnet fitted above the conveyor belt is used to safely extract ferromagnetic parts such as nails, scrap iron and other scrap metals.

                SECONDARY (FINE) SHREDDING | GRANULATION
                The pre-shredded waste wood that is free from foreign particles and metals then enters the second shredding stage. The final product should be homogenous and about 15–30 mm in size to ensure that the recycled material is of high quality throughout for the production of chipboard later on.

                WASTE WOOD PROCESSING FOR RECYCLING PURPOSES

                Waste wood shredding for recycling in the circular economy

                Recycling renewable resources such as wood plays an important part in environmental protection. Wood is often used for pallets, chipboard and demolition wood, etc. At the end of its life large quantities of it end up as waste wood on recycling companies‘ premises. Then particularly clean waste wood can be recycled and reused as a new product (e.g. recycled chipboard).

                Particularly when recycling waste wood, it must be processed in several stages – mostly including these steps:

                • Receipt, weighing and quality control
                • Sorting in accordance with the waste wood grades (A1 - A4)
                • Primary shredding
                • Separating of recyclable material (e.g. metals)
                • Secondary (fine) shredding/granulating


                WASTE WOOD RECYCLING CHARACTERISTICS

                • Particle size 10 - 30 mm
                • Waste wood grades A1, A2
                • Use mostly in the chipboard industry
              • WASTE WOOD FUEL

              • WASTE WOOD PROCESSING FOR INCINERATION

                Powerful performance: The perfect combo of a Lindner Urraco or Miura series twin-shaft shredder with a Lindner Zeta Star screen ensure that the heat will always be turned up in thermal power plants. Together, these two guarantee defined particle sizes at impressive throughput rates. The design is, of course, Lindner style: durable, robust and efficient.

                SHREDDING
                The waste wood is collected in large quantities at the recycling company’s premises and mostly fed directly into the shredder with a wheel loader or a digger. The digger operator first separates the metals etc. during the feeding process. The water spraying system on the shredder makes sure that there is none of the air-born dust usually found while processing wood. The aim here is to shred the material to previously defined output sizes ranging from 80 to 120 mm.

                MAGNETIC SEPARATION OF FERROUS METALS
                The magnetic separator fitted above the discharge conveyor safely extracts ferromagnetic parts such as nails, metal plates and hinges.

                SCREENING
                After shredding, the final particles are further classified. A defined particle size of usually <80 mm, <120 mm or according to the class in line with EN ISO 17225-1 are required for incineration in combined heat and power plants.

                RETURNING OVERSIZED PARTICLES
                Thanks to an integrated system, the screened out oversized particles are returned to the shredder. This eliminates the need to transport the material back into the shredder with a wheel loader.

                TURNING WASTE WOOD INTO FUEL

                Waste wood shredding for energy recovery in thermal power plants

                Energy recovery from waste wood in large biomass power plants has become very popular and is often the only way to recycle large quantities of waste wood in the grades A1–A4, ranging from pallets to old railway sleepers.

                This allows waste wood to be turned into valuable fuel to generate heat and electricity. The recycling process is kept as lean as possible to fuel the power plant with material that has the lowest costs per ton.

                WASTE WOOD FUEL CHARACTERISTICS

                • Standard EN ISO 17225
                • Grain size 80 - 120 mm (categorised in P classes)
                • Waste wood categories A1 - A4
                • Use as fuel in thermal power plants
            • PAPER & PRODUCT DESTRUCTION

                  • PAPER RECYCLING AND DATA DESTRUCTION

                  • PAPER RECYCLING & DATA DESTRUCTION

                    The life cycle of paper products is a much discussed topic. Falling raw material prices and quality are frequently used as buzzwords. Lindner supports a resource-efficient future – with the perfect paper recycling technology. Lindner's tried-and-tested shredding solutions are key in waste paper processing, protecting the environment and saving financial resources. Our system partners use this valuable raw material not only for normal recycling e.g. reuse as paper, but also as insulation. For the latter, the material is shredded and subsequently, after chemical treatment, injected into intermediate walls.

                    ONE-STEP SHREDDING
                    The shredder is key to paper recycling. Depending on the feed, grain sizes of 90% smaller than 20 mm and a throughput of up to 5 metric tons per hour are possible. Thanks to the precise cutting sequence, even data destruction standards can be complied with.

                    SUCTION HOOD
                    The suction hood fitted to the processing machine and discharge ensures clean air and minimises fire risks by transferring even the smallest air-borne particles to the filter.

                    FILTER
                    In this step, the dust captured in the suction process is filtered to ensure a safe and low-particle environment.

                    CONVEYING
                    Conveying technology suited to the machine’s design and processing speed offers the best transport of materials to and from the machine. Thanks to integrated controls, it is not necessary to operate the conveyor belts separately. Lindner’s smart control concept regulates the speed automatically, thus guaranteeing maximum output.

                    MAGNETIC SEPARATION OF FERROUS MATERIAL
                    With our Lindner shredder that is resistant to foreign matter, whole bales or even contaminated materials can be processed. A large over-belt magnet separates metallic parts at the end of the conveyor line, reliably removing scrap metal such as binding wires and other foreign objects.

                    DATA DESTRUCTION IN LINE WITH THE GERMAN DIN66399

                    Shredding of data carriers and files for recycling and repurposing

                    Sophisticated, superior shredding solutions are paramount for defined grain sizes. When it comes to data security, Lindner can build on our years of experience in shredding technology. With our superb technology and tried-and-tested machines, we shred data carriers such as paper, DVDs and magnetic storage media up to security level 5 of the DIN66399.

                    We repeatedly conduct tests that are certified to guarantee premium data destruction for our customers. The environmental considerations are also a huge priority for us: the shredded material can be prepared for recycling and turned into new products.


                    MATERIALS:

                    • PAPER
                    • CARDBOARD
                    • CONFIDENTIAL PAPER
                    • CONFIDENTIAL DATA
              • METAL RECYCLING

                    • LIGHTSCRAP

                    • Scrap metal recycling

                      Metals are precious raw materials that can be recycled and formed into new products almost endlessly

                      SHREDDING
                      When processing light scrap such as scrap iron, sheet metal, aluminium profiles and electronic scrap, the focus is on the shredder. By definition, metals are very resistant to and abrasive in the shredding process. In this step, partially bulky and long metal parts are transformed into a sortable product with greatly reduced volume. The final output is then either directly recycled in the circular economy or is subjected to further processing including being melted down.

                      MAGNETIC SEPARATION OF FERROUS METALS
                      Especially while processing metal profiles or metal frames, over-belt magnets can easily sort out ferrous metals. With this step, higher quality, homogeneous fractions can be achieved (e.g. aluminium scrap).

                      MATERIALS:

                      • LIGHT SCRAP
                      • CAR BODIES
                      • ELECTRONIC SCRAP
                      • ALU PROFILES
                • SHREDDER

                    • STATIONARY PRIMARY SHREDDING

                        • JUPITER 1800I2200I3200

                        • GETS THE PROCESS GOING: RELIABLY HIGH OUTPUT AND CONSISTENT PARTICLE SIZES

                          The Lindner Jupiter single-shaft primary shredder combines everything you need for efficient 24/7 operation: a powerful countershaft drive, a well-engineered machine design and high manufacturing quality. Undefeated by non-shreddables, our tried-and-tested technology ensures a long service life and low maintenance coupled with the necessary power to shred even the toughest materials – year after year and ton after ton.

                          INTERNAL PUSHER
                          Lindner's original:
                          constant material dosing and easy feeding guaranteed.

                          COUNTERSHAFT DRIVE
                          Incredibly powerful – our tried-and-tested drive with extra power to guarantee maximum efficiency and minimum energy consumption.

                          PLUG & GO SCREEN UNIT
                          Easy screen changing – refit screens quickly and very safely.

                          ROBUST SQUARE CUTTING SYSTEM
                          No foreign object can hold back this extremely efficient primary shredder.

                          TORQUE-LIMITING SAFETY CLUTCH
                          The torque-limiting clutch prevents the drive unit from being damaged by blockages caused by foreign objects – long service life guaranteed.

                          HYDRAULIC MAINTENANCE DOOR
                          Access to the cutting system, Lindner style – quick, comfortable and 100% safe.

                          INPUT MATERIALS

                          • MSW
                          • BULKY WASTE
                          • C&I WASTE
                          • WASTE WOOD
                        • TLAS

                        • MERCILESSLY EFFICIENT: PROVEN CONCEPTS INGENIOUSLY APPLIED.

                          The Lindner Atlas is the next big thing in primary shredding. Based on the proven belt concept, the electric drive with a high-performance planetary gearbox delivers the highest efficiency in its class thanks to innovative software controlled energy management. When combined with asynchronous control of the tools, this ensures constant discharge and maximum efficiency, even when one shaft stops. The Atlas also boasts Lindner’s trademark robustness and enormous throughput rates.

                          SHREDDING WITH INTELLIGENT ENERGY MANAGEMENT – THE PERFECT OUTPUT

                          With the new Atlas twin-shaft shredder (a slow-speed, high torque solution), both shafts of the shredding unit can rotate independently while featuring a particularly sturdy frame: perfect for asynchronous and synchronous operation. If one of the two shafts stops due to foreign objects, bulky or tough input materials, the second shaft can still be used in asynchronous operation, ensuring continuous and uniform material discharge. As Lindner Product Manager Stefan Scheiflinger-Ehrenwerth explains, shredding takes place in both directions, enabling a peak throughput of 40 to 50 metric tonnes per hour depending on the input material – even in reverse mode. The robust machine also does not require a pusher/ram: the shafts powerfully pull in material.

                          Optical sorting systems can then recognise and separate significantly more recyclables from the coarsely pre-shredded, evenly discharged material and take it out of the material flow. The Atlas provides the perfect output for sorting technologies and thus the best possible dosage for secondary shredding.

                          What makes the Atlas shredder so unique and innovative – asynchronous, ripping shaft systems have long been available on the market – is the machine’s electric drive concept. Lindner, as a leader in shredding technology, further developed its well-established asynchronous motor belt drive and is now introducing a first: a twin-shaft shredder with intelligent energy management. Stefan Scheiflinger-Ehrenwerth enthuses when describing the company’s latest development: ‘As a result, the machine consumes up to 40% less energy than shredders with conventional hydraulic drives and has even faster reaction times.’ What is more, a container for the oil tank is no longer required: ‘A hydraulic power pack as large as the machine itself is no longer needed.’ Compactly built, the Atlas takes up little space in the client’s facilities.

                           

                      • STATIONARY SECONDARY SHREDDING

                          • KOMET

                          • PRECISION THAT’S A CUT ABOVE THE REST.

                            The Lindner Komet sets new standards in single-shaft shredding. Whether you are processing municipal or bulky refuse, industrial or commercial waste, textiles, waste paper or other materials – the Komet ensures smooth processes 24/7 thanks to its robust design, high-precision tools and smart features. Benefit from its first-rate particle quality and superb efficiency.

                            INTERNAL PUSHER
                            Lindner's original:
                            constant material dosing and easy feeding guaranteed.

                            SINGLE-STEP BELT DRIVE
                            Proven reliability – the standard drive for a long service life and efficient power transmission.

                            PLUG & GO SCREEN UNIT
                            Easy screen changing – refit screens quickly and very safely.

                            HIGH-PRECISION SHEAR CUTTING SYSTEM
                            Precision down to the last cut – Lindner’s solution for defined grain sizes at high throughput rates.

                            TORQUE-LIMITING SAFETY CLUTCH
                            The torque-limiting clutch prevents the drive unit from being damaged by blockages caused by foreign objects – long service life guaranteed.

                            HYDRAULIC MAINTENANCE DOOR
                            Access to the cutting system, Lindner style – quick, comfortable and 100% safe.

                            INPUT MATERIALS

                            • MSW
                            • C&I WASTE
                            • WASTE WOOD
                            • FILM
                          • KOMET HP

                          • GIVES YOUR PROCESSES A BOOST: MORE KNIVES, MORE EFFICIENCY.

                            The Lindner Komet HP is synonymous with high performance in secondary shredding. With an output 60% higher than the standard Komet series and two additional knife rows, the shredder guarantees enormous production capacities. High-precision electronics in combination with particularly robust housing components ensure the machine’s enormous durability, even under the toughest conditions. And it produces consistently high-quality SRF – which is what the name Komet stands for.

                            INTERNAL PUSHER
                            Lindner's original:
                            constant material dosing and easy feeding guaranteed.

                            HIGH PERFORMANCE BELT DRIVE
                            Proven reliability – the standard drive for a long service life and efficient power transmission.

                            PLUG & GO SCREEN UNIT
                            Easy screen changing – refit screens quickly and very safely.

                            HIGH-PERFORMANCE SHEAR CUTTING SYSTEM
                            Seven rows of cutters, over 5000 cuts per minute – our high-performance cutting system for defined grain sizes.

                            TORQUE-LIMITING SAFETY CLUTCH
                            The torque-limiting clutch prevents the drive unit from being damaged by blockages caused by foreign objects – long service life guaranteed.

                            HYDRAULIC MAINTENANCE DOOR
                            Access to the cutting system, Lindner style – quick, comfortable and 100% safe.

                            INPUT MATERIALS

                            • MSW
                            • C&I WASTE
                            • WASTE WOOD
                            • FILM
                          • KOMET PK

                          • HIGH THROUGHPUT, DEFINED RESULTS

                            Set new standards with our Lindner Komet secondary shredder. Whether you are processing municipal or bulky refuse, industrial or commercial waste, textiles, waste paper or other materials – our Komet ensures smooth processes at all times thanks to its robust design, high-precision tools as well as smart features. Benefit from high efficiency as well as first-class SRF/RDF and particle quality.

                            INTERNAL PUSHER
                            Lindner's original:
                            constant material dosing and easy feeding guaranteed.

                            COUNTERSHAFT DRIVE
                            Incredibly powerful – our tried-and-tested drive with extra power to guarantee maximum efficiency and minimum energy consumption.

                            PLUG & GO SCREEN UNIT
                            Easy screen changing – refit screens quickly and very safely.

                            HIGH-PRECISION SHEAR CUTTING SYSTEM
                            Precision down to the last cut – Lindner’s solution for defined grain sizes at high throughput rates.

                            TORQUE-LIMITING SAFETY CLUTCH
                            The torque-limiting clutch prevents the drive unit from being damaged by blockages caused by foreign objects – long service life guaranteed.

                            HYDRAULIC MAINTENANCE DOOR
                            Access to the cutting system, Lindner style – quick, comfortable and 100% safe.

                            INPUT MATERIALS

                            • MSW
                            • C&I WASTE
                            • WASTE WOOD
                            • FILM
                        • STATIONARY ONE-STEP SHREDDING

                              • POLARIS

                              • MAKES SHORT WORK OF SHREDDING: COST-EFFICIENT, HIGHLY RELIABLE AND ONLY ONE STEP.

                                Nothing can withstand the enormous power of the Lindner Polaris single-shaft shredder. Made for one-step processing of untreated municipal, industrial and commercial waste to obtain mid-calorific fuels (40 – 120 mm) ideal for co-incineration in calciners at cement works. Sturdy design and low operating costs are the hallmarks of this highly specialised shredder: enjoy uninterrupted shredding excellence 24 hours a day, seven days a week. With maximum efficiency throughout, as demonstrated by a field test: thanks to the countershaft drive, the Linder Polaris shreds twice as much material as comparable machines in the same period of time.*

                                * Comparative testing at the Chair of Waste Processing and Waste Management, University of Leoben, May 2017

                                INTERNAL PUSHER
                                Lindner's original:
                                constant material dosing and easy feeding guaranteed.

                                COUNTERSHAFT DRIVE
                                Incredibly powerful – our tried-and-tested drive with extra power to guarantee maximum efficiency and minimum energy consumption.

                                PLUG & GO SCREEN UNIT
                                Easy screen changing – refit screens quickly and very safely.

                                ROBUST SHEAR CUTTING SYSTEM
                                Synonymous with durability – maximum output and unaffected by foreign objects.

                                TORQUE-LIMITING SAFETY CLUTCH
                                The torque-limiting clutch prevents the drive unit from being damaged by blockages caused by foreign objects – long service life guaranteed.

                                HYDRAULIC MAINTENANCE DOOR
                                Access to the cutting system, Lindner style – quick, comfortable and 100% safe.

                                INPUT MATERIALS
                                • MSW
                                • BULKY WASTE
                                • C&I WASTE
                                • BALES
                          • STATIONARY UNIVERSAL SHREDDING

                              • UNIVERSO

                              • UNIVERSAL SHREDDING TO THE EXTREME: ROBUST, RELIABLE AND HIGH THROUGHPUT

                                The Universo series with its robust, high-quality engineering ensures a long service life with consistently high throughput rates. Whether you are shredding different types of plastic or waste, with its heavy-duty gearbox drive and robust cutting system there is no job that this shredder cannot handle. As has been proven by thousands of operating hours in different fields of application.

                                INTERNAL PUSHER
                                Lindner's original:
                                constant material dosing and easy feeding guaranteed.

                                HEAVY-DUTY GEARBOX DRIVE
                                Our tried-and-tested, extremely robust gearbox drive ensures maximum torque and uptime.

                                PLUG & GO SCREEN UNIT
                                Easy screen changing – refit screens quickly and very safely.

                                ROBUST SQUARE CUTTING SYSTEM
                                The cutting system that’s resistant to foreign objects: for efficient shredding.

                                TORQUE-LIMITING SAFETY CLUTCH
                                The torque-limiting clutch prevents the drive unit from being damaged by blockages caused by foreign objects – long service life guaranteed.

                                HYDRAULIC MAINTENANCE DOOR
                                Cutting system access, Lindner style – quick, comfortable and 100% safe.

                                INPUT MATERIALS

                                • MSW
                                • BULKY WASTE
                                • FILM
                                • HARD PLASICS
                              • MICROMAT

                              • UNIVERSAL SHREDDING, LINDNER STYLE: FLEXIBLE, INDIVIDUAL AND WELL-ENGINEERED

                                Micromat single-shaft shredders are the answer to your individual shredding needs. A variety of configuration options and special additional features, such as the high-performance or bale-opener design, allow you to adapt the shredder to almost any shredding requirement. A machine that’s been well-engineered down to the last screw.

                                INTERNAL PUSHER
                                Lindner's original:
                                constant material dosing and easy feeding guaranteed.

                                GEAR AND BELT DRIVE
                                Individual solutions for individual drives geared towards your application needs.

                                PLUG & GO SCREEN UNIT
                                Easy screen changing – refit screens quickly and very safely.

                                MADE-TO-MEASURE SHREDDING
                                Variable grain sizes combined with superbly high output.

                                TORQUE-LIMITING SAFETY CLUTCH
                                The torque-limiting clutch prevents the drive unit from being damaged by blockages caused by foreign objects – long service life guaranteed.

                                HYDRAULIC MAINTENANCE DOOR
                                Cutting system access, Lindner style – quick, comfortable and 100% safe.

                                MATERIALS

                                • FILM
                                • HARD PLASTICS
                                • PAPER
                                • CONFIDENTIAL DATA
                              • ANTARES

                              • NEVER LOSES OUT: EFFICIENT TECHNOLOGY IN A COMPACT PACKAGE.

                                With its robust design, easy maintenance access and enormous power, the Antares series combines all the advantages of a Lindner shredder in one compact machine. The wide range of sizes allows you to adapt the shredder to your specific downstream requirements. Enjoy seamless processing with consistent particle size.

                                INTERNAL PUSHER
                                Lindner's original:
                                constant material dosing and easy feeding guaranteed.
                                 
                                HEAVY DUTY GEARBOX DRIVE
                                The heavy duty gearbox drive and motor capacities of up to 90 kW are your ticket to high throughput and small output sizes.

                                PLUG & GO SCREEN UNIT
                                Easy screen changing – refit screens quickly and very safely.

                                PRECISE SQUARE CUTTING SYSTEM
                                Precise cuts in every material – customisable to suit your needs.

                                TORQUE-LIMITING SAFETY CLUTCH
                                The torque-limiting clutch prevents the drive unit from being damaged by blockages caused by foreign objects – long service life guaranteed.

                                SKYLIGHT MAINTENANCE DOOR
                                Cutting system access, Lindner style – quick, comfortable and 100% safe.

                                MATERIALS

                                • FILM
                                • HARD PLASTICS
                                • PAPER
                                • CONFIDENTIAL DATA
                            • MOBILE SHREDDING

                                • URRACO 75

                                • POWERFUL, COMPACT AND VERSATILE

                                  Flexible, powerful, economical. Our Urraco 75 gives you all the advantages of mobile shredding while being extremely compact. This all-rounder shreds even difficult materials with its robust design and powerful engine. Depending on the degree of mobility needed, the machine is available in two chassis versions: either with a wheel axle and tow bar, suitable for hook-lift transport, or with heavy chain traveling gear for off-road mobility on site.

                                  ROBUST TWIN-ROTOR PRINCIPLE
                                  With fully welded crushers, rippers and scrapers.
                                   
                                  HYDROSTATIC DRIVE
                                  Self-regulating hydraulic system with a maximum torque of up to 240,000 Nm.

                                  8" TOUCHSCREEN DISPLAY
                                  Integrated 8" touchscreen display to operate the machine and set parameters

                                  SMART DOUBLE TILTING HOPPER SYSTEM
                                  hydraulically tilting up to 80° on both sides.

                                  SPORTY 375PS DIESEL ENGINE
                                  Fuel-efficient, quiet and eco-friendly – while complying with the latest emission standards.

                                • URRACO 95

                                • ENORMOUS POWER, FULL MANOEUVRABILITY

                                  Take mobile shredding to the extreme with our Linder Urraco 95. Thanks to its extremely powerful engine, long working length and aggressive intake, this twin-shaft shredder makes short work of almost every material. Enjoy an extremely reliable, cost-reducing machine with low wear and tear, easy maintenance and low energy consumption.

                                  ROBUST TWIN-ROTOR PRINCIPLE
                                  With fully welded crushers, rippers and scrapers.
                                   
                                  HYDRAULICS
                                  The hydrostatic drive sports self-regulating hydraulics with a maximum torque of up to 480,000 Nm, crushing material powerfully with its two shafts.

                                  8" TOUCHSCREEN DISPLAY
                                  Integrated 8" touchscreen display to operate the machine and set parameters.

                                  SMART DOUBLE TILTING HOPPER SYSTEM
                                  hydraulically tilting up to 80° on both sides.

                                  POWERFUL 770PS DIESEL ENGINE
                                  Fuel-efficient, quiet and eco-friendly – while complying with the latest emission standards.

                                • MIURA

                                • MAXIMUM FLEXIBILITY, FULL MOBILITY

                                  Full output in changing conditions: our Miura twin-shaft shredder excels in flexibility and mobility. Our innovative FX-Unit (Fast Exchange) allows you to exchange the shafts in minimum time – ideal for quickly adapting the shredder to every material and application. The shredder comes with a tri-axle trailer, making it perfect for moving the machine between different sites swiftly and easily. You really will be going places with this mobile shredding technology.

                                  ROBUST TWIN-ROTOR PRINCIPLE
                                  With fully welded crushers, rippers and scrapers.
                                   
                                  HYDROSTATIC DRIVE
                                  Self-regulating hydraulic system with a maximum torque of up to 240,000 Nm.

                                  9" TOUCHSCREEN DISPLAY
                                  Integrated 9" touchscreen display to operate the machine and set parameters.

                                  SMART DOUBLE TILTING HOPPER SYSTEM
                                  hydraulically tilting up to 80° on both sides.

                                  FX-UNIT
                                  Innovative system to quickly exchange the entire cutting unit.